How to determine whether a vertical long shaft multi-stage drum bag barrel-type Canned turbine pump needs major repairs?...

查看详情

In depth and accurate diagnosis of faults in vertical Multistage semi submersible long shaft deep well turbine pumps...

查看详情

The specific cost of the H-series right angle gearbox in the renovation of power plants (condensate pumps, industrial wastewater pumps, rainwater pumps)...

查看详情

Power plant water supply system and its vertical Multistage long axis semi submersible turbine pump solution...

查看详情

The characteristics of the H series right angle gearbox of HUNAN PERFECT industry are as follows: Diverse models with strong adaptability: offering multiple models such as H60, H125, H200, H300, H425, H750, H1000, H1360, etc.,...

查看详情

Correctly mastering the radial clearance adjustment of the semi submersible vertical multi-stage long shaft deep well turbine pump can extend the service life of the semi submersible vertical multi-stage long shaft deep well turbine pump, improve the working efficiency of the semi submersible vertical multi-stage long shaft deep well turbine pump, and reduce economic losses. After the pump body is installed, the end caps and tiles at both ends can be installed. Adjust the concentricity of the rotor and stator (lift the shaft). The concentricity requirements for the rotor and stator are: half lift equal to half or slightly less than the total lift (considering the rotor's static winding), equal clearance on both sides of the tile mouth, and uniform four corners. Measurement of shaft lifting for semi submersible vertical multi-stage long shaft deep well turbine pump: Before installing the bearing shell, install one dial gauge on each end bearing frame. The center line of the measuring rod of the gauge should be perpendicular to the shaft center line and in contact with the shaft neck. Use a pry bar to lift the shaft smoothly at both ends of the shaft. The difference in readings of the dial gauge when it is in the up and down positions is the total lifting amount of the rotor. Lift up the rotor and place it into the lower tile. At this point, the reading on the dial gauge should be half of the rotor lift and half of the total lift. Otherwise, adjustments need to be made. If there is an adjusting bolt under the bearing frame during adjustment, only loosen or tighten the bolt. If there is no adjusting bolt, the thickness of the gasket under the bearing shell can be adjusted. For the concentricity between the rotor and the stator on both sides, it is generally determined by whether the clearance between the two sides of the bearing is uniform. After placing the lower bearing, use a feeler gauge to measure the clearance between the four bearing holes of the bearing, adjust it evenly, and the clearance on one side of the bearing hole should be half of the clearance at the top of the bearing....

查看详情

This selection guide for vertical Multi-stage barrel-type condensate Turbine Pumps covers the entire process from core parameter verification, scene adaptation, to key points to avoid pitfalls. It allows for direct comparison and selection, avoiding system failures caused by parameter mismatch....

查看详情

The alignment between the diesel engine and the H-series right angle gearbox (90 ° steering) is a key step in ensuring smooth power transmission, reducing vibration, and extending equipment life. The center line of the diesel engine output shaft and the input shaft of the H-series right angle gearbox (90 ° steering) must be adjusted to the same straight line through precise mechanical centering method, with a deviation controlled within 0.05mm....

查看详情

How to select a suitable vertical Canned long shaft barrel-type multi-stage cylindrical bag turbine pump for application in the power industry?...

查看详情

Based on the industry background of high and fluctuating prices of core raw materials such as stainless steel since the first quarter of 2026, there are many new implementation dynamics in the cost control of raw materials for vertical multi-stage long shaft submersible turbine pump head manufacturers. The core focus is on cost reduction and efficiency improvement of core consumables such as stainless steel....

查看详情

Technological breakthrough of vertical semi submersible long axis turbine Deep-well pump in the field of new energy (geothermal/photothermal)...

查看详情

The vertical long axis suspended semi submersible sump pump, with its core characteristics of small footprint, no need to start the pump, and adaptability to complex working conditions of old pipe networks, is the core drainage equipment for old urban areas with limited space and high risk of waterlogging. The vertical long axis suspended semi submersible sump pump is fully suitable for the special needs of drainage renovation in low-lying areas of old urban areas....

查看详情